Audi Q7 Owners & Service Manuals

Audi Q7: Overview - Bosch Generator from 2007

Audi Q7 (4M) 2016-2026 Workshop Manual / Electrical System / Electrical Equipment General Information / Battery, Starter, Generator, Cruise Control / Overview - Bosch Generator from 2007

  Note

The new generators are installed as a running change.

Overview - Bosch Generator from 2007

1 - Nut

  • 65 Nm

2 - Ribbed Belt Pulley

3 - Generator

4 - Voltage Regulator

  • Removing and installing. Refer to → Chapter "Voltage Regulator, Removing and Installing, Bosch Generator from 2007".
  • Carbon brushes, checking. Refer to → Chapter "Carbon Brushes, Checking, All Bosch Generators from 2001"

5 - Bolt

  • 1.5 Nm

6 - Cover

7 - Bolt

  • 3 Nm

8 - Bolt

  • 2.5 Nm

Voltage Regulator, Removing and Installing, Bosch Generator from 2007

Removing

- Remove the generator. Refer to → Electrical Equipment; Rep. Gr.27; Generator; Generator, Removing and Installing.

- Remove the bolts -arrows-.

- Remove the cover -1- on the rear side of the generator.

A27-10157

- Remove the bolts -arrows-.

- Remove voltage regulator -1-.

A27-10158

Installing

- When installing the voltage regulator, make sure the carbon brushes rest correctly on the slip rings.

Install in reverse order of removal, observing the following:

- Install the generator. Refer to → Electrical Equipment; Rep. Gr.27; Generator; Generator, Removing and Installing.

  • Tightening specification. Refer to → Chapter "Overview - Bosch Generator from 2001".

Carbon Brushes, Checking, All Bosch Generators from 2001

Procedure

- Remove the voltage regulator: to 2007. Refer to → Chapter "Voltage Regulator, Bosch Generator from 2001, Removing and Installing", after 2007 → Chapter "Voltage Regulator, Removing and Installing, Bosch Generator from 2007".

- Check the length -a- of the carbon brushes.

  • Wear limit: -a- = 5 mm.

- Install the voltage regulator: to 2007. Refer to → Chapter "Voltage Regulator, Bosch Generator from 2001, Removing and Installing", after 2007 → Chapter "Voltage Regulator, Removing and Installing, Bosch Generator from 2007".

A27-0216

    READ NEXT:

     Overview - Generator, Valeo through MY 2000

    1 - Generator 2 - Voltage Regulator Removing: Remove the nuts -5- and the cover -4-. Remove the bolt -6- and the nuts -7- and remove the voltage regulator. Carbon brus

     Ribbed Belt Pulley without Freewheel, Removing and Installing

    Special tools and workshop equipment required Generator Belt Socket -3310- Inner hex socket 8 mm or TORX T50 Removing - Remove the generator if necessary. Refer to → Electrical Equip

     Windshield Wiper/Washer System

    Washer Fluid Hoses Washer Fluid Line Hose Connections, Disconnecting and Connecting Various hose couplings are used to connect the hoses to the washer fluid pumps and spray jets or as coupling points

    SEE MORE:

     Front Seat, Removing and Installing

    Front Seat, Removing and Installing Special tools and workshop equipment required Trim Removal Wedge -3409- Universal Vehicle Protector -VAS871001- Removing   WARNING Follow all safety precautions when working on pyrotechnic components. Refer to → Chapter "Safety Precautions f

     Cleaning/changing wiper blades

    Fig. 47 Windshield wipers: changing the wiper blades Wiper blade replacement position Switch off the ignition and hold the windshield wiper lever in position (4), fig. 45 until the windshield wiper moves into the wiper blade replacement position. To bring the windshield wipers into the norma

    © 2019-2026 Copyright www.a-q7.com