Audi Q7 Owners & Service Manuals

Audi Q7: Overview - Door

Overview - Door

1 - Door

  • Removing and Installing. Refer to → Chapter "Door, Removing and Installing".

2 - Bolt

  • 33 Nm

3 - Door Arrester

  • Installation position. Refer to → Fig.
  • Removing and Installing. Refer to → Chapter "Door Arrester, Removing and Installing".

4 - Cap

  • For the door arrester
  • Installation position. Refer to → Fig.

5 - Bolt

  • 45 Nm

6 - Upper Door Hinge

7 - Nut

  • 32 Nm

8 - Set Screw

  • 23 Nm

9 - Cap

10 - Bolt

  • 32 Nm

11 - Lower Door Hinge

12 - Bolt

  • 32 Nm

13 - Set Screw

  • 23 Nm

14 - Cap

15 - Bolt

  • 45 Nm

16 - Bolt

  • 8 Nm
  • Replace after removing
  • Quantity: 2

Cap Installation Position

In the installed position, the lettering on the cap -1- must be readable in the upper installation position.

  2 - LEFT UPPER REAR - left / RIGHT UPPER REAR - right

  3 - HL - left / HR - right

A57-10910

Door Arrester Installation Position

In the installed position, the lettering on the door arrester -1- must be readable in the upper installation position:

  2 - HL - left / HR - right

A57-10911

Overview - Door Seals

Overview - Door Seals

1 - Side Sill Seal

  • Removing and Installing. Refer to → Chapter "Side Sill Seal, Removing and Installing".

2 - Inner Door Seal

  • Removing and Installing. Refer to → Chapter "Inner Door Seal, Removing and Installing".

3 - Outer Door Seal

  • Replace after removing
  • Installation position. Refer to → Fig.
  • Removing and Installing. Refer to → Chapter "Outer Door Seal, Removing and Installing".

4 - C-Pillar Seal

  • Installation position. Refer to → Fig.

5 - B-Pillar Seal

  • Installation position. Refer to → Fig.

6 - Seam Seal

q  Removing and Installing. Refer to → Chapter "Seam Seal, Removing and Installing".

B-Pillar Seal Installation Position

  • The vehicle and the seal must be at room temperature.
  • The adhesive surfaces must be free of dirt and grease.
  • If the Bonding Agent -D 355 205 A2- dries longer than 3 hours, then it must be primed again.

- Clean the adhesive surface using the Cleaning Solution -D 009 401 04-.

- Apply Bonding Agent -D 355 205 A2- on the adhesive surface using the Applicator -D 009 500 25- and let dry.

- Remove the protective film, put the seal in the installation position and apply it.

A58-10302

1 - Seal

2 - Inner Door Panel

3 - Outer Door Panel

C-Pillar Seal Installation Position

- Bring the seal into the installation position.

A58-10303

1 - Seal

2 - Outer Door Panel

3 - Inner Door Panel

Outer Door Seal Installation Position

A58-10387

1 - Door Body

2 - Seal

    READ NEXT:

     Door, Removing and Installing

    Removing - Disconnect the door connector -2- from the B-pillar. Refer to → Electrical Equipment; Rep. Gr.97; Connectors. - Tape off the B-pillar in the door arrester area

     Door Arrester, Removing and Installing

      Caution This procedure contains mandatory replaceable parts. Refer to component overview prior to starting procedure. Refer to → Chapter "Overview - Door". Removing - Tape of

     Overview - Window Regulator

    1 - Nut 7 Nm 2 - Window Regulator Removing and Installing. Refer to → Chapter "Window Regulator, Removing and Installing". 3 - Nut 7 Nm 4 - C

    SEE MORE:

     Seat Frame Tunnel-Side Trim Panel, Removing and Installing, Third Row

    Removing - Remove the third row cushion. Refer to → Chapter "Cover and Cushion, Removing and Installing, Third Row Seat Pan". - Remove the expanding clips -2 and 3-, and disengage the upper trim panel -1- the seat frame -arrow-. - Disengage the lower trim panel on the seat

     Overview - Seat Pan Cover and Cushion

    Overview - Seat Pan Cover and Cushion, Seat without Seat Depth Adjuster 1 - Seat Pan 2 - Cushion Cover with cushion, removing and installing. Refer to → Chapter "Seat Pan Cover and Cushion, Removing and Installing, Seat without Seat Depth Adjuster". Cover and cushion

    © 2019-2024 Copyright www.a-q7.com