Audi Q7 Owners & Service Manuals

Audi Q7: Pedestrian Protection Center Crash Sensor -G693-, Removing and Installing

Audi Q7 (4M) 2016-2026 Workshop Manual / Body / Body  Interior / Passenger Protection, Airbags, Seat Belts / Pedestrian Protection Center Crash Sensor -G693-, Removing and Installing

Removing

- Remove the front bumper cover. Refer to → Body Exterior; Rep. Gr.63; Front Bumper; Bumper Cover, Removing and Installing.

- Remove the bolt -1-, and remove the Pedestrian Protection Center Crash Sensor -G693--2- from the bumper.

  WARNING

Before handling pyrotechnic components (for example, disconnecting the connector), the person handling it must "discharge static electricity". This can be done by briefly touching the door striker pin, for example.

- Disconnect the connector -3-.

A69-11207

- To do this pull out the connector lock -2-, push down in direction of -arrow-, and disconnect the connector -1- on the crash sensor.

A69-10928

Installing

  WARNING

  • Follow all safety precautions when working on pyrotechnic components. Refer to → Chapter "Safety Precautions for Pyrotechnic Components".
  • Before handling pyrotechnic components (for example, connecting the connector), the person handling it must "discharge static electricity". This can be done by briefly touching the door striker pin, for example.

- Connect the connector -1- to the crash sensor until it clicks into place in direction of -arrow-.

- Push in the connector lock -2- to secure the connector.

A69-10932

Installation is performed in reverse order of removal, while noting the following:

  Note
  • Make sure the connectors are pushed in all the way and that they engage audibly.
  • Make sure the wires are not pinched.

  WARNING

Repairing pyrotechnic components (for example the airbag and seat belt tensioner) incorrectly increases the risk of unintentional deployments when the battery is connected.

  • The ignition must be on when connecting the battery.
  • For personal safety when connecting the battery, stay out of the deployment area of the airbag and maintain a distance from the seat belt tensioners/seat belts.
  • Make sure that there are no other people inside the vehicle at the time when the battery is connected.

- Connect the battery ground cable with the ignition turned on. Refer to → Electrical Equipment; Rep. Gr.27; Battery; Battery, Disconnecting and Connecting.

  Note

If the Airbag Indicator Lamp -K75- indicates a fault, check the Diagnostic Trouble Code (DTC) memory, erase it and check it again using the Vehicle Diagnostic Tester.

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Pedestrian Protection".

    READ NEXT:

     Pedestrian Protection Crash Sensor, Removing and Installing

    Removing   WARNING Follow all safety precautions when working on pyrotechnic components. Refer to → Chapter "Safety Precautions for Pyrotechnic Components". - Disconnect the batt

     Interior Trim

     Overview - Front Door Trim Panel

    1 - Pull Handle with Armrest Removing and installing. Refer to → Chapter "Front Pull Handle, Removing and Installing". 2 - Liner Mat Insert in the door pocket. 3&nb

    SEE MORE:

     Additionally securing a child safety seat to the top tether anchors

    Fig. 73 (1) Second row rear bench seat / (2) third row rear bench seat: top tether anchors for securing a child safety seat with an upper strap Fig. 74 Rear backrest: securing the upper belt to the top tether anchor Observe the safety precautions. There is a top tether anchor behind every seat

     Manual shifting

    Fig. 92 Center console: shifting manually with the selector lever Fig. 93 Steering wheel: shift paddles You can shift the gears manually when in "D" mode. The transmission is in tiptronic mode. Shifting with the selector lever You can shift into manual shifting mode while the vehicle is stationa

    © 2019-2026 Copyright www.a-q7.com